-
-
-
Tổng tiền thanh toán:
-
Sản phẩm đã được thêm vào giỏ hàng
Số lượng:
Tổng tiền:
M-7016D-G CR 2-channel Strain Gauge Input Module using the DCON and Modbus Protocols with 7-segment LED Display (Gray Cover) (RoHS)
Module 2 kênh đầu vào Strain Gauge + 1 kênh đầu vào số + 4 kênh đầu ra số kết nối RS-485 Modbus RTU & DCON ICP DAS M-7016D
Features
2-channel Strain Gauge Measurement
High Resolution: 16-bit
Excitation Voltage Output: 0 ~ +10 V
50 Hz Event Counter (Digital Input)
High/Low Alarm (Digital Output)
Linear Mapping Function
3000 VDC Intra-module Isolation
Dual Watchdog
Wide Operating Temperature Range: -25 to +75°C
Introduction
In the industrial environment, there are numerous examples where force needs to be converted into a measurable electrical output. In most cases, a strain gauge or a load cell can be used. But the question is, how do we then deal with these electrical output measurements? In this situation, the I-7016 is definitely the No. 1 choice. Not only can the module process data from a load cell or a strain gauge, it also features linear mapping that can be used to directly convert the resulting data into weight via a user-defined correspondent table. The I-7016 supports full-bridge strain gauges and provides 2 Analog Input channels, 1 excitation voltage output channel, 1 Digital Input channels and 4 Digital Output channels. The module provides a programmable input range (±15 mV, ±50 mV, ±100 mV, ±500 mV, ±1 V, and ±2.5 V) and each Analog Input channel can be individually configured. Excitation voltage output can be in the range of 0 ~ +10 V, with a 40 mA driving efficiency. Digital Output channels can also be set as high or low alarm outputs. The M-7016 supports both the Modbus RTU and DCON protocols, which can be configured via software, and all hardware specifications are the same as the I-7016.
Application
Building Automation
Factory Automation
Machine Automation
Remote Maintenance
Remote Diagnosis
Testing Equipment
I/O Specification
Models |
I-7016 |
I-7016D |
M-7016 |
M-7016D |
Strain Gauge Input |
||||
Channels |
2 |
|||
Wiring |
4-wire |
|||
Sensor Types |
Full-Bridge |
|||
Resolution |
16-bit |
|||
Accuracy |
±0.05% of FSR |
|||
Sampling Rate |
2/10 Hz |
|||
Input Impedance |
20 MΩ |
|||
Individual Channel Configuration |
- |
|||
Overvoltage Protection |
±5 VDC |
|||
Open Wire Detection |
- |
|||
Long Distance Measurement |
- |
|||
Excitation Voltage Output |
||||
Channels |
1 |
|||
Range |
0 ~ +10 V |
|||
Max. Load Current |
40 mA |
|||
Resolution |
16-bit |
|||
Accuracy |
±0.05% |
|||
Power-on Value |
Yes |
|||
Digital Input |
||||
Channels |
1 |
|||
Contact |
Dry |
|||
Sink/Source (NPN/PNP) |
Source |
|||
ON Voltage Level |
Close to GND |
|||
OFF Voltage Level |
Open |
|||
Counter (50 Hz, 16-bit) |
Yes |
|||
Input Impedance |
3 kΩ |
|||
Overvoltage Protection |
±30 VDC |
|||
Digital Output |
||||
Channels |
4 |
|||
Type |
Open Collector |
|||
Sink/Source (NPN/PNP) |
Sink |
|||
Load Voltage |
+3.5 ~ +50 VDC |
|||
Max. Load Current |
30 mA/Channel |
|||
Power-on Value |
Yes |
|||
Safe Value |
Yes |
System Specification
Models |
I-7016 |
I-7016D |
M-7016 |
M-7016D |
Communication |
||||
Interface |
RS-485 |
|||
Bias Resistor |
No (Usually supplied by the RS-485 Master. Alternatively, add a tM-SG4 or SG-785.) |
|||
Format |
(N, 8, 1) (N, 8, 2) |
N, 8, 1 |
||
Baud Rate |
1200 to 115200 bps |
|||
Protocol |
DCON |
Modbus RTU, DCON |
||
Dual Watchdog |
Yes, Module (1.6 Seconds), Communication (Programmable) |
|||
LED Indicator/Display |
||||
System LED Indicator |
Yes, 1 as Power/Communication Indicator |
|||
I/O LED Indicator |
- |
|||
7-Segment LED Display |
- |
Yes |
- |
Yes |
Isolation |
||||
Intra-Module Isolation, Field-to-Logic |
1500 VDC |
|||
EMS Protection |
||||
ESD (IEC 61000-4-2) |
- |
|||
EFT (IEC 61000-4-4) |
- |
|||
Surge (IEC 61000-4-5) |
- |
|||
Power |
||||
Reverse Polarity Protection |
Yes |
|||
Input Range |
+10 ~ +30 VDC |
|||
Consumption |
2.4 W |
3.0 W |
2.4 W |
3.0 W |
Mechanical |
||||
Dimensions (L x W x H) |
123 mm x 72 mm x 35 mm |
|||
Installation |
DIN-Rail or Wall Mounting |
|||
Environment |
||||
Operating Temperature |
-25 to +75°C |
|||
Storage Temperature |
-40 to +85°C |
|||
Humidity |
10 to 95% RH, Non-condensing |
Download
Odering information
I-7016 CR |
2-channel Strain Gauge Input Module using the DCON Protocol (Blue Cover) (RoHS) |
I-7016D CR |
I-7016 with 7-segment LED Display (Blue Cover) (RoHS) |
I-7016D-G CR |
I-7016 with 7-segment LED Display (Gray Cover) (RoHS) |
M-7016-G CR |
2-channel Strain Gauge Input Module using the DCON and Modbus Protocols (Gray Cover) (RoHS) |
M-7016D-G CR |
M-7016 with 7-segment LED Display (Gray Cover) (RoHS) |
Số lượng:
Tổng tiền: