Bộ phát và lặp tín hiệu Wi-Fi công nghiệp Access point 2 cổng Gigabit Ethernet Oring IGAP-420_EU

Thương hiệu: Oring | Tình trạng: Còn hàng
Liên hệ

Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100/1000 Base-T(X), EU band

Gọi 0904251826 để được trợ giúp

Bộ phát và lặp tín hiệu Wi-Fi công nghiệp Access point 2 cổng Gigabit Ethernet Oring IGAP-420_EU

Introduction

Overview

IGAP-420+ is a reliable WLAN Access Point with 2 Ethernet Gigabit ports and IEEE 802.11 b/g/n wireless modules. It can be configured to operate in AP/Bridge/Repeater/AP-Client mode. You are able to configure IGAP-420 by WEB interface via LAN port or WLAN interface. IGAP-420 provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IGAP-420 series also provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore, IGAP-420 is one of the best communication solutions for wireless applications on the industrial network.

Features

  • High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed

  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported

  • Support X-Roaming < 60 ms

  • Support wireless load balance

  • Support MAC Filter

  • Support Long Distance Air Connectivity

  • Provide Digital Input and Digital Output

  • Support AP/Bridge/Repeater/AP-Client Mode

  • Switch Mode Supported: Daisy Chain support to reduce usage of switch ports

  • Wireless connecting status monitoring

  • Secured Management by HTTPS

  • Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper

  • Rigid IP-30 housing design

  • DIN-Rail and Wall-mount enabled

Specification

Specifications

ORing AP Model

IGAP-420

IGAP-420+

Physical Ports

 

10/100/1000 Base-T(X) Ports in RJ45 Auto MDI/MDIX

2

5-Pin Terminal Block

2(DI x 4 and DO x 4) :
Dry Contact:
On: short to GND, Off: open
Wet Contact (DI to COM/GND):
On: 0 to 3VDC, Off: 10 to 30VDC

Antenna Connector

2

PoE P.D. Port

-

Present at ETH2
Fully compliant with IEEE 802.3af Power Device specification
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance : 108 ohms min

WLAN Interface

 

Operating Mode

AP/Bridge/Repeater/AP-Client

Antenna and Connector

Reverse SMA Female

Modulation

IEEE802.11b: CCK/DQPSK/DBPSK
IEEE802.11g: OFDM
IEEE802.11n: BPSK, QPSK, 16-QAM, 64-QAM

Frequency Band

America/FCC: 2.412~2.462 GHz (11 channels)
Europe CE/ETSI: 2.412~2.472 GHz (13 channels)

Transmission Rate

802.11b: 11, 5.5, 2, 1 Mbps;
802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps
802.11n:
              20 MHz BW: 130, 117, 104, 78, 52, 39, 26, 13
              40 MHz BW: 270, 243, 216, 162, 108, 81, 54, 27

Transmit Power

IEEE 802.11b: 17dBm ± 1.5dBm@11Mbps
IEEE 802.11g: 16dBm ± 1.5dBm@54Mbps
IEEE 802.11gn HT20: 15dBm ± 1.5dBm @MCS7
IEEE 802.11gn HT40: 14dBm ± 1.5dBm @MCS7

Receiver Sensitivity

IEEE 802.11b : -85dBm ± 2dBm@11Mbps
IEEE 802.11g : -76dBm ± 2dBm@54Mbps
IEEE 802.11gn HT20:-75dBm ± 2dBm@MCS7
IEEE 802.11gn HT40:-72dBm ± 2dBm@MCS7

Encryption Security

WEP: (64-bit ,128-bit key)
WPA/WPA2 PSK :TKIP and AES encryption (802.11i)
802.1X/RADIUS Authentication supported

Wireless Security

SSID broadcast disable

Protocol Support

 

Protocol

ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, STP (IEEE 802.1D)

LED Indicators

 

Power Indicator

3 x LEDs, PWR1(2)(PoE) / Ready:
Red On : Power is on and booting up
Green On : Power is on and functioning Normal

10/100/1000Base-T(X) RJ45 Port Indicator

2 x LEDs,
LNK/ACT:Green for port Act.
Speed: Green for port Link at 1000Mbps
Amber for port Link at 100Mbps.
Off for port Link at 10Mbps

WLAN LEDs

Green Solid On: RF on, Blink: data transmitting
Green for WLAN Strength: 1<25%, 2<50%, 3<75%, 4<100%

Fault

1 x LED, Red for Ethernet link down or power down indicator

Fault Contact

 

Relay

Relay output to carry capacity of 1A at 24VDC

Power

 

Redundant Input Power

Dual DC inputs. 12~48VDC on 6-pin terminal block

Power Consumption (Typ.)

7.5 Watts

8.5 Watts

Overload Current Protection

Present

Reverse Polarity Protection

Present on terminal block

Physical Characteristics

 

Enclosure

IP-30

Dimensions (W x D x H)

74.3(W) x 109.2(D) x 153.6(H) mm (2.93 x 4.3 x 6.05 inch.)

Weight (g)

1150 g

1155 g

Environmental

 

Storage Temperature

-40 to 85°C (-40 to 185°F)

Operating Temperature

-25 to 70°C(-13 to 158°F)

Operating Humidity

5% to 95% Non-condensing

Regulatory Approvals

 

EMI

FCC Part 15, CISPR (EN55022) class A

EMS

IEC61000-4-2 (ESD), IEC61000-4-3 (RS), IEC61000-4-4 (EFT), IEC61000-4-5 (Surge), IEC61000-4-6 (CS), IEC61000-4-8, IEC61000-4-11

Shock

IEC60068-2-27

Free Fall

IEC60068-2-31

Vibration

IEC60068-2-6

Safety

EN60950-1

Warranty

5 years

Order information

Model Name

Description

IGAP-420+_EU

Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100/1000 Base-T(X), 1 port PoE P.D, EU band

IGAP-420+_US

Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100/1000 Base-T(X), 1 port PoE P.D,US band

IGAP-420_EU

Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100/1000 Base-T(X), EU band

IGAP-420_US

Industrial IEEE 802.11 b/g/n wireless access point with 2x10/100/1000 Base-T(X), US band

Download

Datasheet

Preview

Version

Release date

Size

 

DataSheet_IGAP-420(+).pdf

No

 

May 03, 2016

852.93KB

 

Manual

Preview

Version

Release date

Size

 

User Manual_IGAP-420_620_6620 series.pdf

No

 

May 03, 2016

1.93MB

 

MIB

Preview

Version

Release date

Size

 

MIB_ORING.zip

No

 

May 03, 2016

634.88Bytes

 

QIG

Preview

Version

Release date

Size

 

QIG_IGAP-420(+) Series.pdf

No

V1.0

May 03, 2016

1.23MB

 

Firmware

Preview

Version

Release date

Size

 

FW_IGAP-420+.zip

No

V1.1m

May 03, 2016

18.05MB

 

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: