Module truyền thông 1 cổng DeviceNet Master ICP DAS I-8124W

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

I-8124W-G 1 Port DeviceNet Master Module with dual port RAM

Gọi 0904251826 để được trợ giúp

Module truyền thông 1 cổng DeviceNet Master ICP DAS I-8124W

The CAN (Controller Area Network) is a serial communication protocol, and efficiently supports distributed real-time control with a very high level of security. It is an especially suit for networking "intelligent" devices as well as sensors and actuators within a system or sub-system. In CAN network, there is no addressing of subscribers or stations in the conventional sense, but instead prioritized messages are transmitted. As standalone CAN controller, I-8124W can represent an economic solution of DeviceNet application and be a DeviceNet master device in the CAN bus on the DeviceNet network. It is a "Predefined Master connection Set", and supports Group 2 only Server functions to communication with slave devices. It has a independent CAN bus communication port with 5-pin screw terminal connector, and has the ability to cover a wide range of DeviceNet applications. Besides, I-8124W uses the new CAN controller Phillips SJA1000T and transceiver 82C250/251, which provide bus arbitration, error detection with auto correction and re-transmission function. It can be installed in WinPAC or ViewPAC series PAC.It is popularly applied in the industrial automation, building automation,vehicle, marine, and embedded control network. In order to expand the DeviceNet functions of ICPDAS products, I-8124W module is developed for this purpose.



  • 3 indication LEDs (Error,Status,Bus LEDs)

  • Programmable master MAC ID

  • Programmable transfer-rate 125K, 250K, 500K

  • Support maximum nodes up to 64

  • Support Group 2 and UCMM functions

  • The maximum Fragment number is (Input/Output) up to 64

  • Support I/O Operation Mode: Poll, Bit-Strobe and Change Of State/Cyclic

  • Support auto-scan slave device function

  • Support on-line add device into and remove device from network

  • Support auto-reconnect when the connection is broken

We have communicated with the following DeviceNet slaves

  1. Allen-Bradley PowerFlex series DeviceNet Inverters

  2. BECKHOFF CX1500-B520 series DeviceNet I/O modules

  3. BECKHOFF BK5250 series DeviceNet I/O modules

  4. MKS 683 series DeviceNet exhaust throttles

  5. MKS MFC (Mass Flow Controller) series DeviceNet devices

  6. MKS DELTA II FRC (Flow Ratio Controller) series DeviceNet devices

  7. MKS DC Power Generator (OPT- xxx) series DeviceNet devices

  8. OMRON DRT1-ID/ODxx series DeviceNet I/O modules

  9. OMRON DRT2-MDxx series DeviceNet I/O modules

  10. COSMOS PS-7 series DeviceNet gas detectors

  11. CELERITY UNIT IFC-125 series DeviceNet devices

  12. Allen-Bradley PowerFlex AC Drives

  13. Allen-Bradley PowerFlex AC Drives with DriveLogix

  14. Allen-Bradley PowerFlex DC Drives

  15. OMRON DRT2-ID08(-1)/MD16

  16. OMRON DRT2-OD08/MD16-1

  17. OMRON DRT2-OD08-1

  18. OMRON DRT2-ID16(-1)/OD16(-1)


  20. OMRON C200HW-DRT21

  21. Swagelok MS-VCM-D-6-0, MS-VCM-D-6-2 Digital DeviceNet Valve

  22. Swagelok SS-PTX-D-G500-S4-K Digital DeviceNet Pressure-Temperature Transducer

  23. Swagelok SS-PTX-D-G500-SM-K Digital DeviceNet Pressure-Temperature Transducer

  24. Weidmueller SAI-AU M12 DN 16DI/8DO

  25. Weidmueller SAI-AU M12 DN GW 16DI

  26. Weidmueller SAI-AU M12 DN AI/AO/DI

  27. ADVANCED ENERGY Apex RF generators and power-delivery

  28. SMC ITV series Electro-Pneumatic Regulator

  29. SMC Directional Control Valves

  30. SICK DME500 series Distance Sensor

  31. MTS Temposonics R-Series Position Sensors

  32. PFEIFFER VACUUM HiPace series turbopumps

  33. Allen-Bradley(AB) 1769-ADN DeviceNet Adapter

  34. MKS Type T3B and T3P Valves With DeviceNet Interface

  35. ABB DSQC 350A DeviceNet/Allen Bradley remote I/O gateway

  36. MTS Temposonics R-Series sensor

  37. MKS MicroNode I/O series module

  38. LINCOLN Power Wave AC/DC 1000 device

Memory map of Remote I/O

There exist two memory areas, “Input Area” and “Output Area”. The input data of all DeviceNet slaves would be stored in the “Input Area” by DeviceNet master scan engine. Oppositely, the output data of those DeviceNet slaves would be in the “Output Area”. Please refer to the following figure

Users can read a bulk data from “Input Area” in the DeviceNet Master module, like PISO-DNM100U or I-8124W. This bulk data contains multiple devices’ input statuses. If one of the input status of the remote DeviceNet slave changes, the corresponding data located in the “Input Area” would change immediately. Oppositely, the “Output Area” contains multiple devices’ output data. Users may change the output value of a certain device by changing the corresponding data located in the “Output Area”.

Software Utility Features

Hardware Specifications

CAN Interface


NXP SJA1000T with 16 MHz clock


NXP 82C250

Channel number



5-pin screw terminal block (CAN_GND, CAN_L, CAN_SHLD, CAN_H, N/A)

Baud Rate (bps)

125 k, 250 k, 500 k

Transmission Distance (m)

Depend on baud rate (for example, max. 1000 m at 50 kbps )


3000 VDC for DC-to-DC, 2500 Vrms for photo-couple

Terminator Resistor

Switch for 120 Ω terminator resistor


ISO-11898-2, CAN 2.0A and CAN 2.0B


DeviceNet Volumn I ver2.0, Volumn II ver2.0



80186, 80 MHz or compatible


512 KB / 512 KB / 16 KB


CPU built-in


Round LED




WinPAC, ViewPAC, XPAC-CE6 (The XPAC series PAC only support one I-8124W)


For CE5: VB.Net, C#.Net, VC 2005 (with .Net Framework 2.0 or upper), and eVC++ 4.0
For CE6: VB.Net, C#.Net, VC 2008 (with .Net Framework 3.5 or upper)


Power Consumption

2 W



31mm x 115mm x 91mm (W x L x H)


Operating Temp.

-25 ~ 75 ℃

Storage Temp.

-30 ~ 80 ℃


10 ~ 90% RH, non-condensing




Data sheet




Odering information


1 Port DeviceNet Master Module with dual port RAM

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: