Bộ chuyển đổi RS-232/422/485 sang HART ICP DAS I-7570

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

I-7570 CR Serial To HART Converter (Gray Cover) (RoHS)

Gọi 0904251826 để được trợ giúp

Bộ chuyển đổi RS-232/422/485 sang HART ICP DAS I-7570

The I-7570 is a Serial to HART converter designed as the master device of HART protocol. It allows users to access the HART slave by using RS-232 / RS-422 / RS-485. These HART slave devices may be a transmitter, actuator, current output device and so forth. In addition, by using the I-7570 utility tool, users can configure module and test HART communication easily and quickly.

Application

Current Measuring

  • Petrochemical Industry Application

  • Environment Monitoring

  • Tunnel Monitoring

  • Monitor system

  • Building Monitoring

 

 

 

 

 

 

 

 

 

FDT (Field Device Tool) standardizes the communication and configuration interface between all field devices and host systems. FDT provides a common environment for accessing the devices' most sophisticated features. Therefore, by using ICPDAS HART converters, I-7567, I-7570 or I-7547, supporting FDT, users can easily and quickly construct HART online control and configuration system.

HART Device Simulator (called HDS) is the HART device simulation software developed by ICP DAS. It can be used to simulate multi HART slave devices simultaneously to exchange data with HART master device by using ICP DAS HART converter (like: I-7567 / I-7570 / I-7547) connected to any COM port (USB / 232 / 485 / Ethernet). By this way, users can develop or verify the HART master program without any HART slave device.

Features

  • Support HART Short / Long frame

  • Support HART Burst mode

  • Support point-to-point or multi-drop HART mode

  • Support connecting up to 15 HART slave devices

  • Allow two HART masters

  • Provide utility tool for module configuration and HART communication

  • Provide PWR / TxD / RxD indication LED

  • Isolated COM 1: RS-232 / RS-422 / RS-485

  • 4KV ESD Protection

  • Built-in Watchdog

  • Selectable 250Ω load resistor

  • Support HART OPC Server provided by HART COMMUNICATION FOUDATION 

  • Support FDT (Field Device Tool) technique and the below FDT software have been tested OK

Specification

UART Interface

COM 1

RS-232(Tx / Rx / GND) / RS-422 / RS-485

COM 1 Connector

9-pin screwed terminal block

Baud Rate (bps)

1200 bps (For FW_v1.1)
1200 ~ 115200bps (For FW_v1.1 / HW_v1.2)

Data Format

O(odd parity), 8(data bit), 1(stop bit) (For FW_v1.1) 
N/O/E(parity), 8(data bit), 1/2(stop bit) (For FW_v1.1 / HW_v1.2)

HART Interface

HART Interface

2-pin screwed terminal block

HART Channel

1

LED

Round LED

PWR / TxD / RxD

Power

Power supply

Unregulated +10 ~ +30 VDC

Protection

Power reverse polarity protection, Over-voltage brown-out protection

Power Consumption

1 W

Mechanism

Installation

DIN-Rail or Wall Mounting

Dimensions

121 mm x 72 mm x 35 mm (H x W x D)

Environment

Operating Temp.

-25 ℃ ~ +75 ℃ (-13 to 167 ℉)

Storage Temp.

-30 ℃ ~ +85 ℃ (-22 to 185 ℉)

Humidity

5% ~ 95%, non-condensing

Download

Pin

Software

Firmware

Manual

Data sheet

Certification

FAQ

Odering information

I-7570 CR

Serial To HART Converter (Gray Cover) (RoHS)

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: