Bộ chuyển đổi USB sang DeviceNet Master ICP DAS I-7565-DNM

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

I-7565-DNM-G CR USB/DeviceNet Master communication Converter with D-sub 9-pin connector

Gọi 0904251826 để được trợ giúp

Bộ chuyển đổi USB sang DeviceNet Master ICP DAS I-7565-DNM

I-7565-DNM can represent an economic solution of DeviceNet application and be a DeviceNet master device on the DeviceNet network. It is a "Predefined Master-Slave connection Set". I-7565-DNM supports Group 2 only Server and UCMM functions to communication with slave devices. It has an independent CAN bus communication port and has the ability to cover a wide range of DeviceNet applications. Besides, I-7565-DNM uses the new CAN controller Phillips SJA1000T and transceiver 82C250, which provide bus arbitration, error detection with auto correction and re-transmission function.It can be installed on almost any windows-based system, for example Win98/Win2000/WinXP. It is popularly applied in the industrial automation, building automation, vehicle, marine, and embedded control network. In order to expand the DeviceNet functions of ICPDAS products, I-7565-DNM is developed for this purpose.



Communicate with PowerFlex400(English)

SMC Valve Aplications(English)

IFC-125 Valve Aplications(English)

MKS FRCA Valve Aplications(English)

SICK Distance Sensor Aplications(English)

Diagnostic System of Wheeled Tractors Detecting Four Defect's Categories(English)

Selection of Diagnostic Functions in a Wheeled Tractor(English)

Hardware Features

  • Fully compliant with USB 1.1/2.0(Full Speed)

  • No external power supply is required as I-7565 takes it's power from the USB bus

  • DeviceNet Version: Volume I & II, Release 2.0

  • Programmable Master MAC ID and Baud Rate.

  • Baud Rate: 125k, 250k, 500k

  • Support Group 2 and UCMM connection

  • I/O Operating Modes: Poll, Bit-Strobe, Change of State / Cyclic

  • I/O Length: 512 Bytes max (Input/Output) per slave

  • Slave Node : 63 nodes max

  • Support Auto-Search slave device function.

  • Support on-line adding and removing devices

  • Support Auto-detect Group 2 and UCMM device

  • Auto-Reconnect when the connection is broken

  • Status LED: RUN, MS, NS

  • Free Software development tools for Windows

  • Windows XP/ Win7/ Win8/ Win10 32-bit and 64-bit drivers supported

  • Linux drivers supported

Firmware Features

  • Programmable Master MAC ID

  • Programmable transfer-rate 125K, 250K, 500K

  • Each port support maximum nodes up to 64

  • Support Group 2 Only Server functions

  • Support UCMM functions

  • Predefined Master-Slave Connection Set

  • The maximum Fragment number is (Input/Output) up to 64

  • Support I/O Operation Mode: Poll, Bit-Strobe and Change Of State/Cyclic

  • Support Auto-Scan slave device function

  • Support on-line adding and removing devices

  • Support Auto-Reconnect when the connection is broken

We have communicated with the following DeviceNet slaves

  1. Allen-Bradley PowerFlex series DeviceNet Inverters

  2. BECKHOFF CX1500-B520 series DeviceNet I/O modules

  3. BECKHOFF BK5250 series DeviceNet I/O modules

  4. MKS 683 series DeviceNet exhaust throttles

  5. MKS MFC (Mass Flow Controller) series DeviceNet devices

  6. MKS DELTA II FRC (Flow Ratio Controller) series DeviceNet devices

  7. MKS DC Power Generator (OPT- xxx) series DeviceNet devices

  8. OMRON DRT1-ID/ODxx series DeviceNet I/O modules

  9. OMRON DRT2-MDxx series DeviceNet I/O modules

  10. COSMOS PS-7 series DeviceNet gas detectors

  11. CELERITY UNIT IFC-125 series DeviceNet devices

  12. Allen-Bradley PowerFlex AC Drives

  13. Allen-Bradley PowerFlex AC Drives with DriveLogix

  14. Allen-Bradley PowerFlex DC Drives

  15. OMRON DRT2-ID08(-1)/MD16

  16. OMRON DRT2-OD08/MD16-1

  17. OMRON DRT2-OD08-1

  18. OMRON DRT2-ID16(-1)/OD16(-1)


  20. OMRON C200HW-DRT21

  21. Swagelok MS-VCM-D-6-0, MS-VCM-D-6-2 Digital DeviceNet Valve

  22. Swagelok SS-PTX-D-G500-S4-K Digital DeviceNet Pressure-Temperature Transducer

  23. Swagelok SS-PTX-D-G500-SM-K Digital DeviceNet Pressure-Temperature Transducer

  24. Weidmueller SAI-AU M12 DN 16DI/8DO

  25. Weidmueller SAI-AU M12 DN GW 16DI

  26. Weidmueller SAI-AU M12 DN AI/AO/DI

  27. ADVANCED ENERGY Apex RF generators and power-delivery

  28. SMC ITV series Electro-Pneumatic Regulator

  29. SMC Directional Control Valves

  30. SICK DME500 series Distance Sensor

  31. MTS Temposonics R-Series Position Sensors

  32. PFEIFFER VACUUM HiPace series turbopumps

  33. Allen-Bradley(AB) 1769-ADN DeviceNet Adapter

  34. MKS Type T3B and T3P Valves With DeviceNet Interface

  35. ABB DSQC 350A DeviceNet/Allen Bradley remote I/O gateway

  36. MTS Temposonics R-Series sensor

  37. MKS MicroNode I/O series module

  38. LINCOLN Power Wave AC/DC 1000 device

Software Utility Features


This utility supports to search all devices and specific devices in the network. These functions help the users to configure the connection of the slave devices. Anymore, the software also can diagnose the remote slave devices when building the DeviceNet network.


This software supports the users to configure the I/O connection of the devices by searching devices or manual setting. After configuring the I/O connection, the information would be saved into the EEPROM of the I-7565-DNM. The users can export the data from the EEPROM easily. Correspondingly, the users can import the data into the EEPROM.

Remote I/O access

The software utility can easily to access the I/O data of all the slave devices. The users can monitor the input data of the specific slave device and change the output data to the remote slave device with this utility.

DeviceNet for LabVIEW Application Tool

In order to develop complex DeviceNet applications, we provide a LabVIEW driver for this purpose. The I-7565-DNM LabVIEW driver is the function reference to the DeviceNet master. We provide many useful VI functions in the LabVIEW environment. We also have the "DeviceNet Master Utility" to configure the DeviceNet hardware in your PC. The users not only operate easily and develop application rapidly, but also reduce the complexity of applications. The users can communicate with the remote DeviceNet devices in a few simple steps and need not to know about the detail of the DeviceNet protocol. It is the best tool to develop various distributed systems and other industrial applications software on DeviceNet network.

Hardware Specifications




80186, 80 MHz or compatible


512 KB / 512 KB / 16 KB

ESD Protection

2 kV class A

CAN Interface


NXP SJA1000T with 16 MHz clock


NXP 82C250

Channel number



9-pin male D-Sub (CAN_GND, CAN_L, CAN_SHLD, CAN_H, CAN_V+, N/A for others)

Baud Rate (bps)

125 k, 250 k, 500 k

Transmission Distance (m)

Depend on baud rate (for example, max. 1000 m at 50 kbps )


3000 VDC for DC-to-DC, 2500 Vrms for photo-couple

Terminator Resistor

Jumper for 120 Ω terminator resistor


ISO-11898-2, CAN 2.0A and CAN 2.0B


DeviceNet Volumn I ver2.0, Volumn II ver2.0

USB Interface


USB Type B

Transmission speed

921.6 kbps


USB 1.1 and USB 2.0


Round LED




Win XP/ Win7/ Win8/ Win10 32-bit and 64-bit , Linux driver


x64 DLL, .NET DLL, VB6 bas, VC6 DLL, BCB6 DLL


Power supply

By USB interface

Power Consumption

3 W





72mm x 101mm x 33mm (W x L x H)


Operating Temp.

-25 ~ 75 ℃

Storage Temp.

-30 ~ 80 ℃


10 ~ 90% RH, non-condensing









Ordering Information

I-7565-DNM-G CR

USB/DeviceNet Master communication Converter with D-sub 9-pin connector




CAN bus Connector


9-pin Female D-sub & 3-wire CAN bus cable (1M)


7/14 channel Surge Protector


EMI Ferrite Split/Snap-On Core


Field-Installation A-coded 5-pin Female

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: