Bộ chuyển đổi Modbus TCP sang HART ICP DAS HRT-711

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

Modbus TCP to HART Gateway. Communicable over Modbus TCP, HART, RS-232 protocols. Supports operating temperatures of -25°C ~ +75°C (-13°F ~ 167°F) and has a din rail mount.

Gọi 0904251826 để được trợ giúp

Bộ chuyển đổi Modbus TCP sang HART ICP DAS HRT-711

Features

The HRT-711 Modbus TCP to HART Gateway is specially designed for the master device of HART protocol. It allows the Modbus/TCP master device to access the HART slave devices. These HART devices may be a transmitter, an actuator, a current output device and so forth. In addition, we also provide the utility software for users to configure the HRT-711. By using this module, users can integrate their HART devices into Modbus network easily.

  • Support HART Short/Long frame

  • Support HART Burst mode

  • Allow two HART Masters

  • Support Modbus/TCP Format

  • Support Modbus Slave / HART Master Mode

  • Support Firmware Update via Com Port

  • Support On-line Replacement of HART Devices

  • Support Acquire Long Frame Address Automatically

  • Provide LED indicators

  • Built-in Watchdog

  • 4KV ESD Protection

The HART (Highway Addressable Remote Transducer) protocol uses the Bell 202 Frequency Shift Keying (FSK) standard to superimpose digital communication signals on the 4-20 mA loop current shown as below figure. HART communicates at 1200 bps without interrupting and interference with the 4-20mA signal and allows a host application (master) to send/receive digital information from a smart field device. The 4-20mA signal communicates the primary measured value - the fastest and most reliable industry standard. The digital signal can be used for additional device information including device status, diagnostics, additional measured or calculated values, etc. Therefore, the HART communication including analog and digital information provides a low-cost and very robust complete field communication solution that is easy to use and configure. HART is a master/slave protocol which provides for up to two masters (primary and secondary) and the secondary master such as handheld can be used to monitor/control the informatoin of HART bus. HART can be used in various modes such as point-to-point or multi-drop for communicating information to/from smart field instruments and central control or monitoring systems. The following are the description of two main HART operation modes.

  • Relatively easy to understand and use, the HART protocol provides access to the wealth of additional information (variables, diagnostics, calibration, etc.)

  • HART is a no risk solution for enhanced field communication

  • Compatibility with standard 4-20mA wiring

  • Simultaneous transmission of digital data

  • Risk reduction through a highly accurate and robust protocol

  • Increase Plant Availability

  • Reduce Maintenance Costs

  • Improve regulatory compliance

Utitlity

  • Provide the system and communication configuration of HRT-711

  • Provide the Modbus address table for HART command data

  • Provide the diagnostic information of HRT-711 module and HART device

  • Provide send / receive HART command to access HART device

  • Provide "Load/Save" module configuration file to apply to other HRT-711 quickly

Modbus Support

Code

name

Description

01

Read Coil Status

Read the ON/OFF status of discrete outputs in the slave

02

Read Input Status

Read the ON/OFF status of discrete inputs in the slave

03

Read Holding Registers

Read the binary contents of holding registers in the slave

04

Read Input Registers

Read the binary contents of input registers in the slave

05

Force Single Coil

Write a single output in either ON or OFF in the slave

06

Preset Single Register

Write an integer value into a single register in teh slave

15

Force Multi. Coils

Write each coil in teh sequence of coils to either ON or OFF in the slave

16

Preset Multi. Registers

Write a block of contiguous registers in the slave

Specifications

Ethernet Interface

Controller

10/100Base-TX Ethernet Controller (Auto-negotiating, Auto_MDIX)

Connector

RJ-45 x 1 (LED)

UART Interface (For Configuration

COM Port

RS-232 (3 wires)

Connector

3-pin screwed terminal block

HART Interface

HART Channel

1

HART Interface

2-pin screwed terminal block

HART Device

2-wired or 4-wired HART devices

HART Topology

Point to Point or Multi-Drop

HART Data

Only Digital Data

HART Frame Type

Short and Long Frame

Burst Mode

Supported

Max. HART Device

15

Loop Resistor

250 Ω resistor by Jumper

Isolation

UL1577 Spec.

Power

Power Supply

Unregulated +10 ~ +30 VDC

Protection

Power reverse polarity protection, Over-voltage brown-out protection

Power Consumption

1 W

Mechanism

Installation

DIN-Rail or Wall Mounting

Dimensions

72 mm x 35 mm x 121 mm (W x L x H) Detail

Environment

Operating Temperature

-25 ℃ ~ +75 ℃

Storage Temperature

-30 ℃ ~ +85 ℃

Humidity

5% ~ 95% RH, non-condensing

Reference & Support

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: