GW-7434D-G CR: Bộ chuyển đổi Gateway Modbus TCP/RTU/ASCII Slave sang DeviceNet Master

Thương hiệu: ICP DAS | Tình trạng: Còn hàng
Liên hệ

GW-7434D-G CR Modbus/TCP server to DeviceNet master Gateway (RoHS)

Gọi +84 904251826 để được trợ giúp

GW-7434D-G CR: Bộ chuyển đổi Gateway Modbus TCP/RTU/ASCII Slave sang DeviceNet Master

Features

• Programmable DeviceNet Master MAC ID
• Programmable DeviceNet transfer-rate 125K, 250K, 500K
• Supports maximum DeviceNet devices up to 63
• Predefined Master/Slave Connection Set
• Devicenet I/O Length: 128 bytes max. (Input/Output) per DeviceNet slave
• Total DeviceNet I/O Length: 1280 bytes max. (Input/Output) for all DeviceNet slaves
• Supports I/O Operation Mode: Poll, Bit-Strobe and Change Of State/Cyclic
• Supports maximum 512 bytes Modbus I/O datas for DeviceNet I/O to map
• Supports on-line adding device into and removing device from network
• Converters single Modbus/TCP to multi Modbus/RTU, setting by Utility
• Supports VxComm technique for every COM ports of controllers, setting by Utility
• Allowed multi-client (or master) access simultaneously
• Support "Set/Get Explicit Message" methods via Modbus TCP/RTU command
• Supports Modbus RTU to DeviceNet master, setting by Utility

Introduction

The GW-7434D is an economic solution that provides a communication protocol transformation between the DeviceNet protocol and the Modbus TCP protocol. This module solves the problem to connect an existing DeviceNet network to the Ethernet-based PLC, HMI or SCADA for setting up a control or monitoring system. Different to the GW-7243D, the GW-7434D offers the Predefined Master connection Set function and Group 2 only Server function as a DeviceNet master, and enables accessing the DeviceNet slaves automatically and cyclically. If the PLC, HMI or SCADA would like to access the DeviceNet slaves and simultaneously communicate with the Modbus slaves or COM-based devices connected with the RS-232 or RS-485 port of the GW-7434D, the GW-7434D can be the Modbus TCP server or VxComm server to exchange the data with those devices.

Specification

CPU Module
CPU 80186, 80 MHz or compatible
EEPROM 16 KB
Watchdog Timer Yes

 

LED Indicators
Status 1 x Device status
2 x DeviceNet status

 

COM Ports
Ports 1 x RS-232
1 x RS-485
Protocol Modbus ASCII / Modbus RTU
Parity None, Even, Odd
Data Bit 7, 8
Stop Bit 1, 2

 

Ethernet
Ports 1 x RJ-45, 10/100Base-T(X) (Auto-negotiating, Auto_MDIX)
Protocol Modbus TCP

 

DeviceNet
Controller NXP SJA1000T with 16 MHz clock
Transceiver NXP 82C250
Ports 1
Connection Supported 1 connection for Explicit Messaging
1 connection for Polled I/O
1 connection for Bit-Strobe I/O
1 connection for COS/Cyclic I/O
Isolation 1000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Terminal Resistor Jumper for 120 Ω terminal resistor
Specification Volume I, Release 2.0 & Volume II, Release 2.0

 

Power
Input Range +10 VDC ~ +30 VDC
Consumption 2.5 W

 

Mechanical
Dimensions (mm) 72 x 122 x 33 (W x L x H)
Installation DIN-Rail

 

Environmental
Operating Temperature -25 ~ +75 ℃
Storage Temperature -30 ~ +80 ℃
Humidity 10 ~ 90% RH, Non-condensing

Download

Data sheet

Documents

Ordering information

GW-7434D-G     CR  Modbus/TCP server to DeviceNet master Gateway (RoHS)

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: