Module 2 kênh dây rung kết nối Radio modem Campbell Scientific AVW211

Thương hiệu: Campbell Scientific | Tình trạng: Còn hàng
Liên hệ

AVW21192 2 MHz Wireless 2-Channel Vibrating-Wire Analyzer Module

 

Gọi 0904251826 để được trợ giúp

Module 2 kênh dây rung kết nối Radio modem Campbell Scientific AVW211

Overview

The AVW211 is a vibrating-wire analyzer module that includes an internal 920- to 928-MHz spread-spectrum radio for wireless communication. The internal radio's frequency range is used in Australia. This vibrating-wire analyzer module allows our dataloggers to measure vibrating-wire strain gages, pressure transducers, piezometers, tiltmeters, crackmeters, and load cells. These sensors are used in a wide variety of structural, hydrological, and geotechnical applications because of their stability, accuracy, and durability.

The AVW211 uses vibrating-wire spectral-analysis technology (VSPECT™). VSPECT observes the incoming sensor signal, performs a Fourier transform and a spectral analysis (transforming the time series into indivdual sinusoidal components in the frequency spectrum), and determines the sensor frequency by identifying the largest signal in the acceptable range while filtering out environmental and electrical noise.

Benefits and Features

  • Provides better measurements by significantly reducing incorrect readings caused by noise sources

  • Interfaces two vibrating-wire sensors; more sensors may be connected if an AM16/32B multiplexer is used

  • Self-checking diagnostics give continual feedback on sensor condition

  • High resolution—less than 0.001 Hz (industry standard is 0.1 Hz)

  • Low current drain

  • Remote, wireless operation with on-board radio

  • Interfaces both temperature and frequency measurements from vibrating-wire sensors

Detailed Description

The AVW211 uses an innovative spectral-interpolation method for measuring the sensor’s resonant frequency. With the spectral interpolation method, the module excites the vibrating-wire sensor, measures the response, performs a Fourier transform on the response, and returns the result with a resolution better than 0.001 Hz—all within two seconds. Because spectral analysis can distinguish signal from noise on the basis of frequency content, this method offers improved immunity to competing noise.

The AVW211 module also provides many self-checking diagnostics such as vibrating-element signal strength, signal-to-noise ratio, vibrating-element signal decay ratio, and incorrect signal response. These diagnostics can be running in the background to give continual feedback of the condition for each sensor.

The AVW211 typically transmits its data to an RF411A spread-spectrum radio that is connected to the datalogger. The AVW211 can also be connected directly to the datalogger.

Specifications

Internal Radio Frequency Range

920 to 928 MHz

Radio Power

250 mW 
Older AVW211 analyzer modules (serial # < 11676) have 100 mW radios.

Number of Vibrating-Wire Sensors Measured

Up to 2 vibrating-wire sensors can be connected to the analyzer module. Additional sensors can be measured by using an AM16/32-series multiplexer.

Power Requirements

9.6 to 16 Vdc

Analog Input/Outputs

2 differential (DF) vibrating-wire measurements (V+ and V-) and 2 single-ended (SE) ratiometric resistive half-bridge measurements (T+ and T-) for vibrating-wire sensor's onboard temperature sensor.

Digital Control Ports

3 digital control ports (C1 – C3)

  • C1 functions as an SDI-12 I/O communication port.

  • C2 functions as a Clk output for multiplexer control.

  • C3 functions as a reset output for multiplexer control.

RS-232 Port

1 9-pin RS-232 port (for connecting to a datalogger COM port)

Measurement Resolution

0.001 Hz RMS (±250 mV differential input range; -55° to +85°C)

Measurement Accuracy

±0.013% of reading (±250 mV differential input range; -55° to +85°C)

Input Voltage Range

±250 mV (differential)

Common Mode Range

±25 V

Baud Rates

Selectable from 1200 to 38.4 kbps (ASCII protocol is one start bit, one stop bit, eight data bits, and no parity.)

Memory

  • Either 128 or 512 kB of SRAM

  • 2 MB of OS Flash

Dimensions

21.6 x 11.18 x 3.18 cm (8.5 x 4.5 x 1.2 in.)

Weight

0.43 kg (0.95 lb)

Typical Current Drain @ 12 Vdc

Quiescent, Radio Off

~0.3 mA

Radio Duty Cycling 1 s

~3 mA (includes quiescent current)

Radio Always On

~26 mA

Active RS-232 Communication

~6 mA

Measurement

~25 mA

Download

Brochures

AVW200-series Vibrating-Wire Modules

Vibrating-Wire Spectral Analysis Technology (VSPECT)

Manuals

AVW200-series 2-Channel Vibrating-Wire Spectrum Analyzer Modules

Sản phẩm đã được thêm vào giỏ hàng

Số lượng:

Tổng tiền:

Sản phẩm đã được thêm vào giỏ hàng

Phí vận chuyển: Tính khi thanh toán

Tổng tiền thanh toán: